Saito FA170 3-Cylinder Radial SAIE170R3, Full Gasoline CH Ignitions CDI Conversion.

Saito FA170 3-Cylinder Radial SAIE170R3, Full Gasoline CH Ignitions CDI Conversion.

Saito FA200 3-Cylinder Radial SAIE200R3, Full Gasoline Conversion

Saito FA200 3-Cylinder Radial SAIE200R3, Full Gasoline Conversion

Saito FA200R 3-Cylinder Radial SAIE200R3, GLOW CH Ignitions CDI Conversion.

Hi Quality CH Ignitions & Hardware to convert your engine to Ignited Glow Fuel or any other Ignitable fuel mixture you are able to mix.

Saito 200 3-Cylinder Radial SAIE200R3

$235.00
In stock
Only 3 left
SKU
SAIFA200R3-GLOW

Hi Quality CH Ignitions & Hardware to convert your engine to Ignited Glow Fuel or any other Ignitable fuel mixture you are able to mix.

Saito 200 3-Cylinder Radial SAIE200R3

CH introduced this conversion first time in 2012 when the first CDI was developed and tested.
Now we offer a full CH Ignitions GLOW CDI conversion kit to get the engine running.

  • GLOW Spark Plug GAP 0.35 mm / 0.0135″
  • No more than 15% Nitro
  • Must use 7.4v 2 cell LIPO 2300mah minim 2700-5000mha

Usually we have all hardware in stock, CDI is build as ordered.

The specifications of the CH CDI you will find it on the 3 Cylinder CH CDI Page.

This conversion is one of the best option if you want to keep running on Glow Fuel or any other ignitable fuel.
Once converted to CH CDI you can run pretty much any fuel type you can mix.
You can run  ZERO Nitro if you want to stay with GLOW FUEL, this will be a more economical option.
By running ZERO Nitro the internal components of the engine will be more protected from rusting.
After Run Oil will still be a good  practice.

By Converting to CH Ignitions Glow CDI you will get a better Idle, better engine behavior all around and up to 25% more run time on the same tank of fuel.
To accomplish this you MUST LEAN (turn in) the needles 1 turn at list BEFORE you attempt to start and go from there.
Fuel will be burned out 99% and you will not have to clean up the messy Glow from the plane.

We also offer full install and test run Service for a flat rate of $100 ( 2 hour labor) and many times we go way over 2 Hours.

Included Hardware:

  • 1 x CH CDI Made in the USA
  • 1 x Magnet adjustable ring
  • 1 x Sensor holder with sensor
  • 3 x 1/4-32 Spark Plug   ( same thread as your glow plug)
  • 2 x M3 x 14 mm  cap screw

Time 30 Degrees BTDC when sensor/Magnet on cyl #1 first come in contact.

Saito 170 3-Cylinder Radial SAIE170R3 GLOW CH IGNITIONS CDI CONVERSION

SAITO 170R3 , 200 R3 Glow CH Ignitions Glow Conversion

Videos

For more details on timing please watch video below

If you still have questions, Please do not hesitate to call me, as a CH customer…you are a phone call away !

Saito FA200R3 Running on Gasoline, with Glow will be same but without the Gasoline Carburetor.

HOW TO TIME AN ENGINE 2 ST or 4 ST

Manuals

Please download, watch online or print out for your convenience.

Saito 450 Radial Install Instructions for Glow or Gasoline same Procedure apply for Saito 90,120,170,200R3 parts look different sizes and shape but the basic is the same as far as sensor, magnet ring, timing, all have same concept.

Saito R450 Install Instructions

CH Timing Procedure

CH Universal Timing Device

Write Your Own Review
You're reviewing:Saito FA200R 3-Cylinder Radial SAIE200R3, GLOW CH Ignitions CDI Conversion.